- 您现在的位置：买卖IC网 > Sheet目录366 > TMDXEVM5515 (Texas Instruments)EVAL MODULE DSP FOR C55XX
SPRS645F – AUGUST 2010 – REVISED OCTOBER 2013
2.5.4
EMIF Terminal Functions
Table 2-8. External Memory Interface (EMIF) Terminal Functions
SIGNAL
NAME
NO.
TYPE (1)
(2)
OTHER (3)
(4)
DESCRIPTION
EMIF FUNCTIONAL PINS: ASYNC (NOR, SRAM, and NAND)
Note: When accessing 8-bit Asynchronous memory:
?
?
Connect EM_A[20:0] to memory address pins [22:2]
Connect EM_BA[1:0] to memory address pins [1:0]
For 16-bit Asynchronous memory:
?
?
Connect EM_A[20:0] to memory address pins [21:1]
Connect EM_BA[1] to memory address pin [0]
This pin is multiplexed between EMIF and GPIO. For EMIF, this pin is the EMIF
IPD
external address pin 20.
EM_A[20]/GP[26]
J3
I/O/Z
DV DDEMIF
BH
Mux control via the A20_MODE bit in the EBSR (see Figure 3-3 ).
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR2 register.
This pin is multiplexed between EMIF and GPIO. For EMIF, this pin is the EMIF
IPD
external address pin 19.
EM_A[19]/GP[25]
G4
I/O/Z
DV DDEMIF
BH
Mux control via the A19_MODE bit in the EBSR (see Figure 3-3 ).
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR2 register.
This pin is multiplexed between EMIF and GPIO. For EMIF, this pin is the EMIF
IPD
external address pin 18.
EM_A[18]/GP[24]
G2
I/O/Z
DV DDEMIF
BH
Mux control via the A18_MODE bit in the EBSR (see Figure 3-3 ).
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR2 register.
This pin is multiplexed between EMIF and GPIO. For EMIF, this pin is the EMIF
IPD
external address pin 17.
EM_A[17]/GP[23]
F2
I/O/Z
DV DDEMIF
BH
Mux control via the A17_MODE bit in the EBSR (see Figure 3-3 ).
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR2 register.
This pin is multiplexed between EMIF and GPIO. For EMIF, this pin is the EMIF
IPD
external address pin 16.
EM_A[16]/GP[22]
E2
I/O/Z
DV DDEMIF
BH
Mux control via the A16_MODE bit in the EBSR (see Figure 3-3 ).
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR2 register.
This pin is multiplexed between EMIF and GPIO. For EMIF, this pin is the EMIF
IPD
external address pin 15.
EM_A[15]/GP[21]
N1
I/O/Z
DV DDEMIF
BH
Mux control via the A15_MODE bit in the EBSR (see Figure 3-3 ).
The IPD resistor on this pin can be enabled or disabled via the PDINHIBR2 register.
EM_A[14]
EM_A[13]
EM_A[12]/(CLE)
EM_A[11]/(ALE)
EM_A[10]
M1
L1
K1
K2
L2
I/O/Z
I/O/Z
I/O/Z
I/O/Z
I/O/Z
DV DDEMIF
BH
DV DDEMIF
BH
DV DDEMIF
BH
DV DDEMIF
BH
DV DDEMIF
BH
This pin is the EMIF external address pin 14.
This pin is the EMIF external address pin 13.
This pin is the EMIF external address pin 12. When interfacing with NAND Flash,
this pin also acts as Command Latch Enable (CLE).
This pin is the EMIF external address pin 11. When interfacing with NAND Flash,
this pin also acts as Address Latch Enable (ALE).
This pin is the EMIF external address pin 10.
(1)
(2)
(3)
(4)
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal, BH = Bus Holder
Input pins of type I, I/O, and I/O/Z are required to be driven at all times. To achieve the lowest power, these pins must not be allowed to
float. When they are configured as input or high-impedance state, and not driven to a known state, they may cause an excessive IO-
supply current. Prevent this current by externally terminating it or enabling IPD/IPU, if applicable.
IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 3.8.1 , Pullup/Pulldown Resistors .
Specifies the operating I/O supply voltage for each signal
Copyright ? 2010–2013, Texas Instruments Incorporated
Product Folder Links: TMS320C5515
Device Overview
21
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
TMDXEXP1808L
KIT EXPERIMENTER FOR AM180X
TO263-3EV-VREG
BOARD EVAL TO220-3/TO263-3 VREG
TO263-5EV-VREG
EVAL BOARD VREG TO220-5/TO263-5
TOOLSTICK-EK
KIT TOOL EVAL SYS IN A USB STICK
TPS23757EVM
EVALUATION MODULE FOR TPS23757
TPS62230EVM-370
EVAL MODULE FOR TPS62230-370
TRAVELCUBE
SURGE SUP 1OUT W/RJ11 DIRECTPLUG
TRAVELER100BT
SURGE SUP 2OUT W/RJ11 DIRECTPLUG
相关代理商/技术参数
TMDXEVM5515
制造商:Texas Instruments 功能描述:TMS320C5515 DSP Evaluation Module
TMDXEVM642
制造商:Texas Instruments 功能描述:Tools Development kit For Use
TMDXEVM6424
功能描述:开发板和工具包 - TMS320 C6424 DSP Eval Mod RoHS:否 制造商:Texas Instruments 产品:Experimenter Kits 工具用于评估:F2802x 核心:TMS320 接口类型:UART, USB 工作电源电压:
TMDXEVM6446
制造商:Rochester Electronics LLC 功能描述:DAVINCI EVM BUNDLE W/O EMULATOR - Bulk 制造商:Texas Instruments 功能描述:DAVINCI EVM BUNDLE W/O EMULATOR - Bulk
TMDXEVM6446T
制造商:Texas Instruments 功能描述:DM6446 DIGITAL VIDEO EVALUATION MODULE - Boxed Product (Development Kits)
TMDXEVM6446TS
制造商:Texas Instruments 功能描述:DM6446 DIGITAL VIDEO EVALUATION MODULE - Trays
TMDXEVM6452
功能描述:开发板和工具包 - TMS320 C6452 EVM Evaluation Module RoHS:否 制造商:Texas Instruments 产品:Experimenter Kits 工具用于评估:F2802x 核心:TMS320 接口类型:UART, USB 工作电源电压:
TMDXEVM6455
功能描述:开发板和工具包 - TMS320 C6455 Evaluation Module RoHS:否 制造商:Texas Instruments 产品:Experimenter Kits 工具用于评估:F2802x 核心:TMS320 接口类型:UART, USB 工作电源电压: